Maintenance

Maintenance

Maintenance of the wood-burning stove should only be performed when it is not in use/cool. Daily maintenance is limited to a minimum. The easiest cleaning method is to vacuum the outside of the stove with a small nozzle with soft bristles, or to dust with a dry, soft cloth or dust broom. Always remember that the stove must be cool before cleaning it. Do not use water, spirit or any other kind of cleaner, as this will damage the lacquer. The stove should be thoroughly cleaned once per year. Ash and soot must be removed from the combustion chamber.

The door and the locking fastenings must be greased with copper grease.

Emptying the ash pan or pot

The ash pan is most easily emptied by pulling a waste bag over the pan, turning the pan upside down, and then carefully pulling it up and out of the bag again. Ash is to be disposed of via refuse collection.

Emptying the ash pot Stoves with ash pots (the HWAM 3310, HWAM 3320 and HWAM 4410) are equipped with pipes for sucking out ash.

Open the ash hatch at the bottom of the wood-burning stove. The wheel underneath the stove is turned one revolution in the direction of the arrow, by which means the ash from the combustion chamber is shaken down into the ash pot, and simultaneously swept towards the pipe opening. This procedure can be repeated if the pot is very full. Remove the cap from the pipe, place the hose to the ash pan on to the pipe and turn on the motor/vacuum cleaner.

Please note: the ash must be completely cool before it is removed from the wood-burning stove.

Be aware that embers in the ash can remain hot up to 24 hours after the fire in the stove has gone out!

Service Inspection

At least once every other year, the wood-burning stove should receive a thorough, preventative service inspection. Among other things, the service inspection covers:

A thorough cleaning of the wood-burning stove.

Greasing the hinges with copper grease.

Inspection/possible replacement of seals. Seals between the door and glass must always be replaced.

Adjustment of the handle/door.

Inspection of the automatics system.

Possible replacement of springs in the automatics system.

Inspection/possible replacement of heating insulation material.

The inspection is to be performed by a qualified professional. Use only original spare parts.

Cleaning

Before cleaning your wood-burning stove, the regulator knob must be turned to the minimum setting in order to prevent soot and ash from coming out in to the automatics system.

 


 


Baffle Plate
Baffle plate is taken out. Push the plate forward and lift it up a bit to the side. Tilt one side down, and the plate becomes free and can be removed from the combustion chamber. The iron baffle plate is taken out. The transport safety catch is straightened out. The plate is lifted free of the hooks and is afterwards removed.

Insulation
Over time, the combustion chamber’s effective yet porous insulation can become worn and damaged. A crack in the back plate can cause secondary air to become incorrectly distributed in the combustion chamber, and it should therefore be replaced. A crack in the side plate will not affect the efficiency of the wood-burning stove.

However, the side plates and smoke shelf should be replaced when they are worn down to half their original thickness.

Door/Glass
Ensure that the air slits in the door frame are free of ash and soot particles.

If the glass door is sooty, it can be cleaned with lightly moistened paper dipped in ash. Regularly check to make sure that seals in the door are complete and soft. If not, they should be replaced. Use only original spare parts. All parts can be purchased from your local dealer.

Door Lift (HWAM 3310, HWAM 3320, HWAM 4410, HWAM 3410. HWAM I 30/55)
The mechanism for the door lift consists of a chain drive that is positioned on each side of the wood-burning stove, and a spring that is located underneath the stove. If the door opens and closes too slowly, it can help to grease the chain wheel's bushing and door hinges with copper grease. This should be done once a year. If the door opens and closes too quickly, it generally means the spring has become too loose. It can be tightened by using a special tool. Ask your local HWAM dealer for assistance.

Please Note: You should always get a professional to grease and repair these parts.

Surface
It is normally not necessary to treat the surface. Any possible damage to the lacquer should, however, be repaired using Senotherm spray. Senotherm can be purchased at the dealer.

Cookie policy

At HWAM A/S we use cookies on our website. Cookies give us information about how you use our website and they help us give you the best experience when you visit hwam.com    

We principally use cookies to measure our website traffic. This information is shared with third parties.
Read more about our cookie policy here

OK